SEAGATE TECHNOLOGY, INC.
       Customer Technical Support FAX Network +1 408 438-8137
     Customer Technical Support Bulletin Boards (300-9600, 8-N-1)
ЪДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДВДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДї
і United States    +1 408 438-8771 і  United Kingdom +44 628 478011  і
ГДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДЕДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДґ
і Germany         +49  89 140-9331 і  Singapore      +65   227-2217  і
АДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДБДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДЩ
                            (C)opyright 1991



ST-1162N (94351-160) Swift SCSI

     ЪДДД\
     і 0 і  5
     і 0 і  G
     і 0 і  G
     і 0 і 12  ....................  o o o o o o
     АДДД/     1...................  o o o o o o
     ННННСННННННСНСННННННСНСННННННСНННННННННННННН
         1ДДДДДДЩ 1ДДДДДДЩ 1ДДДДДДЩ  1 2 4 і і і
           Terminator Resistors      ДДВДД і і і
                                       і   і і і   Terminator Power Select
            Drive ID, binary - use ЕДДДЩ   і і і   Header located on the side
             ID 0 (no jumpers) for і       і і і   ДДДДДДДДДДДДДДДДДДДДДДДДДД
              single drive install Щ       і і і  (Back) A B (Front of drive)
            Enable Parity Checking ДДДДДДДДЩ і і         C D
         Enable Motor Start Option ДДДДДДДДДДЩ і      ННСННННННННННPНWНA
              Synchronized Spindle ДДДДДДДДДДДДЩ        і
                                                        і
              ЪДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДЩ
             ДЕД
             A-B      Drive from Power Connector (factory default)
             A-C      Drive from SCSI Bus
             A-C&B-D  Drive from Power Connector and Provide to SCSI Bus
             B-D      Only provide to SCSI Bus

                 Swift with Shrouded SCSI Connector
     ЪДДД\
     і 0 і  5    ЪД If the SCSI connector has a plastic shroud,
     і 0 і  G    і   note pin-1 on cable and T-res.
     і 0 і  G    і
     і 0 і 12 ЙНННННННННННННННННННН» o o o o o o
     АДДД/    є:::::::::::::::::::1є o o o o o o
     ННННСННННННСНСННННННСНСННННННСНННННННННННННН
         АДДДДДД1 АДДДДДД1 АДДДДДД1  1 2 4 і і і
           Terminator Resistors      ДДВДД і і і
                                       і   і і і   Terminator Power Select
            Drive ID, binary - use ЕДДДЩ   і і і   Header located on the side
             ID 0 (no jumpers) for і       і і і  ДДДДДДДДДДДДДДДДДДДДДДДДДД
              single drive install Щ       і і і  (Back) A B (Front of drive)
            Enable Parity Checking ДДДДДДДДЩ і і         C D
         Enable Motor Start Option ДДДДДДДДДДЩ і      ННСННННННННННPНWНA
              Synchronized Spindle ДДДДДДДДДДДДЩ        і
                                                        і
              ЪДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДДЩ
             ДЕД
             A-B      Drive from Power Connector (factory default)
             A-C      Drive from SCSI Bus
             A-C&B-D  Drive from Power Connector and Provide to SCSI Bus
             B-D      Only provide to SCSI Bus


                             ST-1162N
                         94351-160 Swift

       UNFORMATTED CAPACITY (MB) ________________162
       FORMATTED CAPACITY (29 SECTORS/1 SPARED)__137.5
       ACTUATOR TYPE ____________________________VOICE COIL
       TRACKS ___________________________________9,612
       CYLINDERS ________________________________1,068
       HEADS ____________________________________9
       DISCS ____________________________________5
       MEDIA TYPE _______________________________THIN FILM
       RECORDING METHOD _________________________RLL
       TRANSFER RATE (mbytes/sec) _______________1
       SPINDLE SPEED (RPM) ______________________3,600
       BUFFER ___________________________________32 or 64 Kbyte
         Read Look-Ahead, Non-Adaptive,
         Single-Segmented
       INTERFACE ________________________________SCSI
       TPI (TRACKS PER INCH) ____________________1,350
       BPI (BITS PER INCH) ______________________22,840
       AVERAGE ACCESS (ms) ______________________15
       SINGLE TRACK SEEK (ms) ___________________4
       MTBF (power-on hours) ____________________70,000
       POWER REQUIREMENTS: +12V START-UP (amps) _2.5
                           +12V TYPICAL (amps) __0.7
                           +5V START-UP (amps) __0.75
                           +5V TYPICAL (amps) ___0.4
                           TYPICAL (watts) ______11
                           MAXIMUM (watts) ______34
       BUFFERED STEP PULSE RATE (micro sec) _____6-200
       WRITE PRECOMP (cyl) ______________________N/A (1069)
       REDUCED WRITE CURRENT (cyl) ______________N/A (1069)
       LANDING ZONE (cyl) _______________________AUTO PARK
       IBM AT DRIVE TYPE ________________________0 or NONE

Already low-level formatted at the factory.


                          Swift Remote LED Option

               Front View of Drive Without the Plastic Bezel

                                  ЪДДДВДДДї
                                  і A і B і    B = Anode
                                  ГДДДЕДДДґ    D = Cathode
                                  і C і D і
              ...НННННННННННННННННПНННПНННПНННННPНWНAННН...


        ш Default jumper at C-D for LED mounted on drive PWA
        ш To use remote LED, remove jumper and extend B (Anode)
          and D (Cathode).
        ш Swift LED kit 75912397 allows connection to a remote LED
        ш Swift LED kit 95913369 has an LED for attachment to the
          system front bezel or a 5.25-inch frame kit

Seagate reserves the right to change, without notice, product
offerings or specifications. (6/26/90)